Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Discovering Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
We have come across this great article about How to Install a Bathtub directly below on the net and decided it made good sense to talk about it with you over here.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the job can move quickly; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the task is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have qualified on your own for the job and also fit trying it. Rather than employing a service provider to take over a halfway-completed project, it is better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have currently acquired a new tub and also do not need to transform the plan of your previous supply of water pipelines.
Your devices and product checklist need to make up the following:
Planning for the Setup
First of all, the supporting framework supplied with the bath ought to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be quite troublesome due to the restricted accessibility that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a towel prepared for the staying water that will certainly originate from the pipelines. Once the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning during this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also readjusting the feet on the bathtub up until the level reads level.
To install faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water system and inspect all joints and new pipework for leakages and tighten them if essential. Fill up the bath tub as well as likewise check the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and also securing around the bath tub must wait up until the bathtub has actually been used at least once as this will resolve it into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the various other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washing machines remain in place in between the tap and the sink. Safeguard the tap in place with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The former kind must be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the installation can move enough to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealant can break rather very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our section on A Step-by-Step Guide to Installing a Bathtub. Thank you for taking time to read through our blog. Enjoyed our entry? Please share it. Let another person check it out. Thanks so much for taking the time to read it.
Dial, and relax! Report this page